<tbody id="lvxjo"><noscript id="lvxjo"></noscript></tbody>
<dd id="lvxjo"></dd>

網站公告:

產品中心

濟南精拓流體設備有限公司

電話:0531-69951198

郵箱:jingtuolt@163.com

傳真:0531-69951198

地址:濟南市歷城區西周南路9號

網址:http://www.aiqin1.cn

業內資訊

當前位置:首頁 - 新聞中心 - 業內資訊 - 管道增壓泵的一般操作流程

管道增壓泵的一般操作流程

發布時間:2017-03-24 15:09:50   發布人:http://www.aiqin1.cn
  對于全自動的管道增壓泵,除了在首次調試運行時需要注意操作外,平時使用一般是無需人為操作的。下面重點介紹非全自動的管道增壓泵操作流程,一般是分為啟動、運轉、停止三個步驟。
  For fully automatic pipeline booster pump, in addition to outside the debug runtime needs to pay attention to the operation for the first time, use at ordinary times is generally without artificial operation. The following focuses on the automatic pipeline booster pump operation, is usually divided into start-up, operation, stop three steps.
  一、起動操作流程管道增壓泵
  First, starting operation process
  在泵與電機連接時一定要將泵軸(泵轉子)向上提起1-2mm,然后再擰緊聯軸器上的螺栓;
  In the connection of the pump and motor must lift pump shaft (pump rotor) up 1 to 2 mm, then tighten bolts on coupling;
  泵在起動前必須用手轉動泵轉子,感覺靈活;
  Pump must turn the pump rotor by hand before starting, flexible;
  泵在起動前必須使泵內充滿水和排除空氣(泵出水段的螺塞有水噴出為止),然后關閉出口閘閥;
  The pump before starting the pump must be made full of water and air (water pump section of screw water jet), then close the exit gate valve;
  接通電源,泵起動。打開壓力表,逐漸打開出口閘閥直到壓力表指到所需壓力為止。
  Connected to the power supply, the pump starts. Open the pressure gauge, gradually open the export gate valve until the pressure gauge refers to the required pressure.
  二、運轉
  Second, the operation
  注意電機軸承溫度,最高溫度不得高于70℃。運轉時軸承不應有噪音。
  Pay attention to the motor bearing temperature, the highest temperature is not higher than 70 ℃. There should be no noise of the bearing during operation.
  注意經常檢查泵聯軸器下部的壓蓋是否有水漏出,正常情況下應不泄露或只有微量的液體存在于壓蓋內。如有較大的泄漏,就應調整或更換壓蓋內的機械密封。
  Often pay attention to check whether there is a gland at the bottom of the pump shaft coupling, a water leak under normal circumstances should not leak or only trace amounts of liquid present in the gland. If there is a large leakage, you should adjust or replace the mechanical seal in the gland.
  水泵工作10000小時后,應進行檢修。葉輪與密封環的半徑間隙因磨損超過0.5mm,就應及時更換密封環。
  Water pump working after 10000 hours, should be for maintenance. Impeller and seal ring due to wear and tear more than 0.5 mm, the radius of the clearance seal ring should be timely replacement.
  三、停機
  Third, stop
  慢慢關閉出水閘閥和壓力表,然后關閉增壓泵的電源。如果所處環境溫度較低時,則應放出泵內的水,以免凍裂。長期停止使用水泵時,應將泵拆開,擦干零件上的水,并在滑動面上涂以防銹油,妥善保存。
  Slowly shut out of the water gate valve and pressure gauge, then close the power of the pump. If environment temperature is lower, it should be out of the water in the pump, so as to avoid frost crack. Stop for a long time when using water pumps, pump should be open, dry the water on the parts, and in the sliding surface coated with anti-rust oil, properly kept.
  我們會用優良的、貼切的服務,讓顧客感受到親情般的溫暖,始終視顧客的安全如己如親。我們會用自然優勢打造產品的獨特之處,從而給消費者帶來享用產品時獨特的心境。
  We will use good and appropriate service, to make the customer feel the family warmth, always regards the customer's safety as yourself as close. We will made products unique natural advantages, thereby bringing consumers enjoy products unique state of mind.

13188935873

qq

2018狗不理玄机1一1 枝江市| 无为县| 尚义县| 新兴县| 同心县| 华宁县| 邵武市| 固镇县| 固安县| 美姑县| 北川| 常熟市| 宜城市| 莱州市| 莱芜市| 巴林右旗| 江津市| 甘南县| 澄城县| 仪陇县| 临沭县| 开江县| 弥勒县| 中西区| 阜新市| 杭锦旗| 潞城市| 哈巴河县| 祥云县| 长兴县| 娱乐| 桃园市| 鹿邑县| 北流市| 肃南| 江永县| 张家港市| 康保县| 辽宁省| 石林| 甘孜县| http://so.yhza9b.top http://www.116in.cn http://www.ba7lu8.cn http://m.4nspwd.top http://www.an425.cn http://wap.lsje39.pw