<tbody id="lvxjo"><noscript id="lvxjo"></noscript></tbody>
<dd id="lvxjo"></dd>

網站公告:

產品中心

濟南精拓流體設備有限公司

電話:0531-69951198

郵箱:jingtuolt@163.com

傳真:0531-69951198

地址:濟南市歷城區西周南路9號

網址:http://www.aiqin1.cn

網站公告

當前位置:首頁 - 網站公告 - 氣動液體增壓泵的選型要注

氣動液體增壓泵的選型要注意哪些?

發布時間:2018-11-22 14:20:02   發布人:http://www.aiqin1.cn
1.工作壓力和流量
1. Working Pressure and Flow
氣動增壓泵和動力單元的工作壓力參照驅動氣壓為0.48Mpa時泵輸出壓力和流量。如果泵的最大輸出壓力大于所需的工作壓力,這就要考慮安全措施。對于最大輸出壓力,請參照產品目錄中的“靜態下驅動氣壓力和輸出液壓近似比率表”。動力單元的選型與泵一致。對于工作流量,請參照產品目錄中的“性能曲線圖”。
The working pressure of pneumatic booster pump and power unit refers to the output pressure and flow rate of the pump when the driving pressure is 0.48Mpa. If the maximum output pressure of the pump is greater than the required working pressure, safety measures should be considered. For maximum output pressure, please refer to the "Approximate Ratio Table of Driving Pressure and Output Hydraulic Pressure under Static Conditions" in the catalogue. The selection of power unit is consistent with that of pump. For workflow, please refer to the "Performance Curve" in the product catalog.
2.驅動氣體的壓力和流量
2. Pressure and flow rate of driving gas
氣動增壓泵和動力單元在連續工作時使用的驅動氣壓不超過0.69Mpa,在間歇工作時可達到1.03Mpa。在最佳性能狀態時氣動泵的耗氣量,請參照所需驅動氣體流量表。
The driving pressure of pneumatic booster pump and power unit is not more than 0.69 Mpa in continuous operation and 1.03 Mpa in intermittent operation. In the best performance state, the air consumption of the pneumatic pump, please refer to the required driving gas flow meter.
3.輸送液體介質
氣體增壓泵
3. delivery of liquid media
氣動增壓泵泵輸送的液體介質是氣動增壓泵的選型中著重考慮的部分。液壓部分的材質和液壓密封圈是由輸送的液體介質所決定的。泵可用油、水和大多數液體介質。標準泵的主要液壓密封圈是丁橡膠和聚氨酯,單向閥座采用特氟龍密封。其它密封材料包括碳氟化合物和亞乙基丙烯,這些密封材料主要用于輸送的特殊介質。請向工廠或當地的分銷商咨詢密封材料選型。
The liquid medium conveyed by pneumatic booster pump is an important part in the selection of pneumatic booster pump. The material quality of the hydraulic part and the hydraulic seal ring are determined by the liquid medium conveyed. Pumps can use oil, water and most liquid media. The main hydraulic sealing rings of standard pumps are polybutadiene rubber and polyurethane, and the one-way seat is sealed with Teflon. Other sealing materials include fluorocarbons and ethylene propylene, which are mainly used for special media for transportation. Please consult the factory or local distributor for seal material selection.
4.氣動增壓泵可接受的體積和重量對于某些的應用,氣動增壓泵和動力單元的外形尺寸和重量也要重點考慮
4. For some applications, the acceptable volume and weight of pneumatic booster pump and power unit should also be taken into account.

13188935873

qq

2018狗不理玄机1一1 黄浦区| 绥江县| 河西区| 二连浩特市| 湛江市| 郸城县| 濉溪县| 和田县| 张掖市| 抚顺县| 诸暨市| 广丰县| 安福县| 松溪县| 云和县| 当涂县| 陆川县| 衡阳县| 福安市| 贵州省| 广西| 新沂市| 广元市| 河源市| 中宁县| 屏山县| 宣城市| 威信县| 滁州市| 吴忠市| 车险| 米林县| 潜江市| 伊金霍洛旗| 耿马| 泽库县| 太原市| 亳州市| 建阳市| 勃利县| 霸州市| http://www.kuaisan2h.cn http://v.sinaam0b.pw http://v.elo3vy.top http://game.7bcmt8.top http://china.sina47i.pw http://m5.7t41uo.top